CONFIGURATION MANUALVersion 11.01 - November 2012
EVS Broadcast Equipment S.A.- November 2012VIII What's New?
The following screenshot highlights the Port settings, defined on page 1 of the Channelstab in the server-based application:RS422 #1 - #6Description S
Channels and Control SettingsIntroductionThe Channel and Control settings mainly allow specifying which controllers (main andpossibly secondary) have
Main ctrl (Main Controller)Description Name of the main device/controller allowed to control the givenplay or record channel.Values For a controller t
OSDDescription Specifies which device (main or secondary controller) willmanage the OSD display characters in parallel mode.Values Two values are poss
Protocol-Specific Assignment RulesStandalone ProtocolThe table shows whether or not the given protocol, used as a standalone (as maincontroller, witho
Remote IPDP AVSP VDCP Sony EditRec Odetics DD35OdeticsF&KVDCPF&KLinXMain Controller1 PGM 22 PGM> 2 PGM1 PGM+ 1 REC11 REC> 1 RECSeveral P
Remote IPDP AVSP VDCP Sony EditRec Odetics DD35OdeticsF&KVDCPF&KLinX1 PGM2 PGM> 2 PGM1 REC 1> 1 REC1 PGM+ 1 RECSeveral PGM+ 1 RECSeveral
Exclusive mode - REC ChannelsThe following table shows the supported protocol combinations in exclusive mode onrecord channels.Secondary >Primary v
Parallel mode - REC ChannelsThe following table shows the supported protocol combinations in parallel mode on recordchannels.Secondary >Primary vRe
Recorder SettingsIntroductionThe Recorder settings allow specifying configuration settings associated to the recordchannels.These fields are available
1. Introduction1.1. Introduction to the Configuration of EVSServersNew Configuration ModuleThe Multicam Setup application is used for configuration an
Clip CapacityDescription Recording mode on the record channels.Values The following values are available: Global / Per channel• Global:In this mode, t
IN1 XX% LoopWarningA change to this parameter requires an application reboot (ALT+Q from theoperational windows) to be taken into account.Description
Supported Modes1 PGM ModeIn a single PGM mode, users working in a Spotbox configuration with IPDirector no longerneed to use two channels in PGM/PRV m
Mix on One Channel SettingsIntroductionThe Mix on one channel settings allow specifying whether the secondary link of the codecmodule (J3) of the play
3.4.3. AudioAudio and Audio Monitoring SettingsIntroductionThe Audio settings allow users to specify, among others, the physical configuration foraudi
Audio ConnectorsDescription Type of connectors available in the hardware configuration.The audio formats available on the EVS server, and in theAdvanc
Ancillary ModeAvailability This setting is displayed in SD configurations.Description Encoding method used for digital audio.Values 20 Bits / 24 Bits
Overview on Advanced Audio SettingsIntroductionThe Advanced Audio settings are defined from the Channels tab, pages 3 to 6 of theMulticam Configuratio
General PrinciplesThe advanced audio settings are presented on each page as a table:In the table, the information is organized as follows:• The rows c
Audio Input SettingsDescriptionThe advanced audio input settings allow users to specify:• which type of audio source should be taken into account in t
• a configuration section for each configuration line. It is presented in seven tabs whicheasily give access to all configuration parameters:Simplific
Example 2The allocation of the source audio mono channels shown above means that:• The embedded audio source of the 1st mono channel of the record cha
Audio Output SettingsDescriptionThe audio output settings for audio allow users to:• map the audio mono channels of the material stored on the EVS ser
XS Server- Version 11.01- Configuration Manual3. Multicam Configuration 112
ExampleIn the screenshot displayed below, the audio mono channels defined on the A/V materialon the EVS server are allocated to the play channels in t
Audio (Embedded) InputsBy default, the audio embedded mono channels from the source material are mapped asshown in the table below onto the A/V materi
Audio Embedded OutputsBy default, the audio mono channels from the A/V material stored on the EVS server aremapped to the embedded mono channels on th
The table shows the maximum number of players, and the audio configuration with 8tracks (mono channels):OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6Mono1 D 01
Audio AnalogBy default, the audio mono channels of the A/V material stored on the EVS server are sentto the analog audio output connectors of the play
Collective Editing ActionsYou can apply the following editing actions to all audio channels of a page using thefollowing shortcuts, when available on
The audio gain can be adjusted by steps of 0.75dB, 3dB or 6dB, in the range from-77.25dB to +23.25dB of the current audio level.The following screensh
Configuration Available from Server, Web and RemotePanelYou can configure the EVS server using one of the three available tools:• The server-based app
Dolby Audio ManagementConcepts• Dolby Digital or Dolby 5.1 or AC-3, is an audio coding system containing up to 6discrete channels of sound, with 5 cha
The Dolby E transitions will be correct as long as:• the configuration is correct• the AES stream containing Dolby E is correctly synchronized with th
LTCDescription Longitudinal timecode (timecode defined on or plugged into theEVS server) automatically stored in the first timecode jumptable (LTC tab
Timecode Insertion SettingsIntroductionThe Timecode Insertion settings allow the management of VITC or ANC timecodeschannel by channel.These fields ar
In LoopD-VITCThe D-VITC (Digital Vertical Interval Timecode) and userbits are always written on themonitoring SD outputs of the record codec and are t
UserBitsDescription Enables/disables the insertion of the user bits in the HDoutput.The values specified for the HAnc LTC and HAnc VITC fieldshave to
UserBitsDescription Enables/disables the insertion of the user bits in the SDoutput.When TC0 is selected for the D-VITC field, the user bitsvalues wil
Supported PacketsThe supported ancillary data packets shall comply with the SMPTE standards 334M,291M (type 2 ANC packet).Up to now, SMPTE 334M data p
Custom 1/2Description Enables/disables a customized decoding of the SMPTE 334Mdata packets. See section "Customizing the Decoding ofSMPTE Data&qu
3.5. Network Tab3.5.1. OverviewNetwork TabThe Network tab consists of one page in the basic and/or advanced mode in the server-based application. The
Documented User InterfacesThe Server Configuration manual deals with all user interfaces used to configureMulticam: server-based application, web-base
3.5.2. SDTI SettingsIntroductionThe SDTI settings allow specifying the settings related to the SDTI network. Thisnetwork allows the content between EV
SpeedDescription Enables the selection of the SDTI option and the bandwidth forthe network.On the XS server, there is one pair of SDTI connectors: XNe
TypeDescription Defines the privileges of the EVS server on the SDTI network.Values The following values are possible:• Client: It cannot access the c
3.5.3. Gigabit Ethernet SettingsIntroductionThe Gigabit Ethernet settings specify the settings related to the Gigabit Ethernetnetwork. It allows the b
IP Address (Port 1/Port 2)Description IP address to connect to the port #1/port #2 of the GigabitEthernet connection on the EVS server.Values The IP a
3.6. Monitoring Tab3.6.1. OverviewMonitoring TabThe Monitoring tab consists of one page in basic mode (there are no advancedparameters) in the server-
Setting Name Basic & AdvancedTechnicalSetupJ1 X XOUT B J3 X XAspect ratio X XSD Edge Enh. X XREC HD->SD Low latency X X3.6.2. Multiviewer Setti
LayoutDescription Specifies how the sources are displayed on the Multiviewerscreen.Values • 4 (2+2)• 6 (4+2)• 6 (3+3)• 8 (3+3+2) (not useful on all se
Display 1 to 8Description Specifies the source linked to the corresponding display in theselected layout. You can select play channels (PGM), recordch
Aspect ratio - SD downconvertedDescription Changes the aspect ratio of the video output in SD mode.Values • 16:9 Anamorphic• 4:3 Crop• 4:3 LetterboxDe
When Starting the EVS Server After Initial ConfigurationAfter the initial configuration, you will select a configuration line and press ENTER to runth
The following screenshot presents the settings page of the Monitoring tab in the server-based application and highlights the OSD settings area:Genlock
Network errorDescription Enables or disables the network error information display onthe output monitor.If there is an problem with the network connec
Char OUT J4Description Specifies the monitoring output type generated on the J4connector.Values • SD• HDDefault value System dependentChar OUT J1Descr
SDEdge Enh.Description Defines the edge enhancer strength used when generating theSD downconverted output video.Values 0 to 100Default value 66RECHD
3.7. Protocol Tab3.7.1. OverviewProtocol TabThe Protocol tab consists of 3 pages in the basic mode and 4 pages in the advanced modein the server-based
Setting Name Basic AdvancedTechnicalSetupOSD Settings P2 / P3 P2 / P3 T5.XOSD on Output X X XDisplay sel – X XTC H-Pos – X XTC V-Pos – X XName H-Pos –
3.7.2. RS422 Protocols SettingsIntroductionThe RS422 Protocols settings allow specifying the settings related to the clipidentification used to access
3.7.3. Clip IdentifiersLSM IDThe LSM ID is a clip identifier based on the EVS video server structure.The LSM ID is made up of 3 digits and 1 letter, f
3.7.4. Sony BVW SettingsIntroductionThe Sony BVW settings allow specifying the settings that will be used with the SonyBVW75 protocol.These fields are
Use guardbandDescription Makes the OUT guardband available to the protocol.Values • Yes, meaning that the protocol has access to the IN andOUT guardba
2. Multicam Setup2.1. Overview of User Interfaces2.1.1. Overview of the Setup AreasGeneral DescriptionThe Multicam Setup window is the window that ope
Overview on Edit Rec SettingsThe Edit Rec settings allow specifying the settings that will be used by the Edit Recfeature.The Edit Rec settings are av
Playlist Settings for Edit RecIntroductionThe Playlist settings allow specifying the playlist that will be loaded by default when theEdit Rec starts.T
Audio Settings for Edit RecIntroductionThe Audio settings allow specifying the settings related to the fading applied at the clipboundaries.The follow
Time Code Settings for Edit RecIntroductionThe Time Code settings allow specifying the timecode (TC) types used in variouscommunication protocols.The
Insert TC in SDI (1 or 2 fields)Description Activates or deactivates the timecode insertion in the VITC inSD or in the HANC in HD when the playlist is
Channel Settings for Edit RecIntroductionThe Channel settings allow specifying the settings related to the channel behavior instop mode.The following
OSD Settings for Edit RecIntroductionThe OSD settings allow specifying the settings related to the OSD and information to bedisplayed on the monitorin
Display selDescription Specifies the field or combination of fields to be displayed onthe screen.• The TC is the Edit TC or the User TC in case the co
Name V-PosDescription Defines the vertical position of the edit name on the screen.Values 0 to 11Default value 03.7.6. RS422VarID SettingsIntroductio
VarID Definition and ParametersThe VarID is a 32-bytes ID with variable length and format. The VarID settings enableVDCP protocol to use the VarID to
The following screenshot presents the Multicam Setup window in the web-basedinterface:7 2. Multicam SetupEVS Broadcast Equipment S.A. - November 2012
VarID Configuration FileThe VarID parameters are defined in a configuration file. This file, named varid.ini, islocated in the C:\LSMCE\DATA directory
LengthDescription Specifies whether the VarID has a fixed length of 8 bytes or avariable length of 32 bytes.Values • 8, fixed length.• 32, variable le
3.8. GPI Tab3.8.1. OverviewGPI TabThe GPI tab consists of one page in basic mode (there are no advanced parameters) in theserver-based application. Th
3.8.2. GPI SettingsIntroductionThe GPI Settings allow specifying the settings related to the GPI inputs and outputsfeatures.These fields are available
• DD35: Play, Pause, Recue, Previous, Next, Skip.• Odetics: Play, Pause, Recue, Next.• VDCP: Play, Pause, Recue, Previous, Next, Skip.NoteFor all prot
GPIs IN - FunctionDescription Specifies the function associated to the GPIinput line.According the configured protocol some or all of the functionsde
GPIs IN - DelayDescription Specifies the time (number of seconds and/or frames) that theserver will wait after receiving the input signal before execu
GPIs OUT - Pulse durationDescription Defines the pulse duration (number of seconds and/or frames)for pulse type output lines.Values • 00s00fr to 02s00
How to Activate the Tally FunctionTo use the tally function, proceed as follows:1. Activate it using the Tally parameter.2. Go to the GPIs IN settings
3.9. Operation Tab3.9.1. OverviewOperation TabThe Operation tab consists of six pages in the basic mode in the server-based application.No advanced mo
Description of the AreasThe table below describes the various parts of Multicam Setup window:# Name of area Description1. Title bar The title bar disp
Clips SettingsSetting Name BasicOperationalSetupClips settings P1 to P2 2.xAutomake clip for cam A/B/C/D P1 XMake clips rem. trains P1 XGuardbands P1
Miscellaneous SettingsSetting Name BasicOperationalSetupProtection settings P3 5.1Protect pages X XClip edit by network X XConfirm delete clips/playli
Setting Name BasicOperationalSetupCall channel VGA X XPGM/PRV mode X XInternal loop mode X XGrab X XBrowse button X XDefault XFile X X3.9.2. OSD Setti
Keyword infoDescription Shows / hides the defined keywords and ranking on the OSDof the output monitors when the clip is loaded on its Short INpoint.A
Audio metersDescription Shows/hides the audio meters on the OSD.Values Yes / NoDefault value YesDB AdjustDescription Adjusts the value of the displaye
3.9.4. Clips SettingsIntroductionThe Clips settings relate to various aspects of the clip management: clip definition,storage location, metadata, and
Automake clip for CAM A/B/C/D/EAvailability This parameter is only displayed in XSense configurations.Introduction When creating clips, the clip corre
Default clip durationDescription Specifies the duration of clips created with only one referencepoint (IN or OUT point).Values Disable, or from 00s01f
Clip post-rollDescription When the Post-Roll function is enabled from the secondaryclip menu, the clip will play through its OUT point for theduration
Record trains OUTsDescription Specifies whether Multicam will freeze or play through when itreaches an OUT point marked on the record train that is be
# Name of area Description4. ConfigurationSummaryThis area shows a summary of the server parametersfor the configuration line selected in the Configur
Freeze on cue pointsDescription Specifies whether Multicam will freeze or not when it reachesa cue point marked on the record train that is being play
3.9.5. Playlist SettingsIntroductionThe Playlist settings relate to various aspects of playlist management and effects.These fields are available in t
Video effect durationDescription Sets the duration of video transition effect. The specified valueis used as default value in the Playlist Edit mode.N
Confirm Ins/Del clipsDescription Specifies whether a confirmation will be required each time theoperator wants to add a clip to the playlist or remove
Fade to/from colorDescription Specifies the color that is used in the transition effects ‘fade tocolor’, ‘fade from color’ and ‘fade to/from color’ (V
The following screenshot presents page 3 of the Operation tab in the server-basedapplication, where the Protection settings are available, and highlig
Clip edit by networkAvailability This setting is only available if the license code 117 is valid.Description Allows users to edit clips on the whole S
3.9.7. Keywords SettingsIntroductionThe Keywords settings allow the management of keywords on the EVS server.These fields are available in the followi
Keyword filesDescription Specifies the keywords file that can be used to assignkeywords to clips or to search the clips database.Values The following
3.9.8. Push SettingsIntroductionThe Push settings relate to the management of the Push function on the EVS server. ThePush function allows users to ea
Configuration LinesIn the Configuration Lines area, a configuration line is highlighted when it is selected.The main commands for configuration line m
Push TargetDescription Specifies which EVS servers will be listed as possible targetsfor push actions when the user selects:• the default Target 1 and
Push Target 1 / 2Description Specifies to which machine(s) on the network the clips mustautomatically be sent when the operator uses the PUSHfunction
Push Receive PageDescription Specifies the page of your machine where clips sent to you byother network operators using the PUSH function must bestore
Audio slow motionDescription Allows users to play back or mute the audio track when theplaying speed is different than 100%.Values The following value
Aux track outputDescription Specifies to which audio outputs the auxiliary track of theplaylist will be played out.Values The following values are pos
The following screenshot presents page 4 of the Operation tab in the server-basedapplication, where the EVS Controller settings are available:Effect d
Second lever rangeContext The lever can be used in normal mode to play back clips atslow motion speed from 0 to 100%. A secondary range isavailable to
Pointing deviceDescription Specifies the pointing device connected to the EVS server,and initializes it.If the tablet is not properly calibrated, this
Call channel VGADescription Enables or disables the Call Channel function on the VGAClip screen. This function allows the operator to select onwhich P
Grab imageAvailability This setting is only available if the license code 117 is valid.Description Enables / disables an image grab when the MARKkey
Configuration LinesCommand description Command iconRenaming the configuration lineEntering the Configuration window to edit the settings related theco
GlossaryGGPIAbbreviation for General Purpose Interface. This refers to a device used as ancommunication interface with the EVS server. It has digital
PPhysical channelPhysical connection to a connector on a codec module of a V3X board that used andassigned as a player or record channel in a given co
To learn more about EVS go to www.evs.comCorporate+32 4 361 7000North & Latin America+1 973 575 7811Asia & Pacific+852 2914 2501Other regional
2.2.2. Launching a ConfigurationIntroductionWhen the EVS server has initialized, the Multicam Setup window stays open, by default,until the operator s
2.2.3. Editing a ConfigurationHow to Edit a ConfigurationIntroductionWhen the operator hits a key on the keyboard connected to the EVS server (within
Invalid ConfigurationInvalid configuration lines are easily detected in the server-based application:• When a configuration line becomes invalid, a re
2.2.5. Exporting and Importing Configuration LinesHow to Export Configuration LinesNoteThe screenshots in this section features configuration names wh
3. If requested, change the selection of configuration lines selected for export on the leftpane:◦ By default, a cross is displayed in front of all co
2. Click Export next to the configuration line you want to export.3. In the File Download dialog box, click Save.4. Select the location where you will
3. On the left pane, use the UP ARROWor DOWN ARROW key to highlight the folderthat contains the configuration file you want to import.When the folder
In the Web-Based InterfaceNoteIn the web-based interface, it is only possible to import configuration lines one byone.To import configuration lines on
CopyrightEVS Broadcast Equipment S.A.– Copyright © 2011-2012. All rights reserved.DisclaimerThe information in this manual is furnished for informatio
2.2.6. Changing the Position of Configuration LinesIn the Server-Based ApplicationTo move a configuration line up in the list in the server-based appl
In the Web-Based InterfaceThe feature to copy and paste configuration lines is not available as such in the web-based interface.You can however use th
2.3. Server Parameters2.3.1. Chapter ContentsThe table below presents the topics of this section and shows whether the describedfeatures are available
In the Server-Based ApplicationTo assign a server facility name in the server-based application, proceed as follows:1. In the Multicam Setup window, p
The password protection has the following impact on the various user interfaces:• The password is required to apply changes to configuration parameter
Deactivating the Password on the EVS ServerOnce the password protection is active, it can only be deactivated from the server-basedapplication as foll
SettingsThe MTPC board connection settings are described in the table below:Setting DescriptionIP Address Specifies the IP address to connect to the p
Supported FormatsThe supported date format is DD-MM-YYYY, as shown in the example below:• 15-03-2011 for March 15, 2011The supported time format is hh
2.3.6. Setting the Default Output To VGA/VideoIntroductionBetween the PC boot and the I/O boot, the video driver is loaded. The Default Output toVGA/V
Overview on the Raid Configuration WindowThe Raid Configuration window is available from the Multicam Setup window, whenpressing R to call the Raid Co
EVS Broadcast Equipment S.A.- November 2012II
Field DescriptionThe following table describes the fields editable in the Requested Configuration area in theRaid Configuration window. The fields are
2.4. Licenses and Maintenance2.4.1. Overview on Options Codes ManagementIntroductionTo run a software application and/or specific software options, no
2.4.2. Options Codes Management WindowIn the Server-Based ApplicationThe window features three areas which contain the information mentioned below:Are
In the Web-Based InterfaceThe window features two areas which contain the information mentioned below:Area DescriptionCentral area All codes available
2.4.3. Entering and Removing License CodesIntroductionWhen you request new license codes to activate one or more features, you can receivethe license
In the Web-Based InterfaceTo enter a new license code delivered via a COD file, proceed as follows:1. Copy the .COD file onto a drive available from y
In the Web-Based InterfaceTo enter a new license code delivered via a key number, proceed as follows:1. From the Multicam Setup window, click Options
2.5. Server Maintenance2.5.1. Chapter ContentsThe table below presents the topics of this section and shows whether the describedfeatures are availabl
ProcessThe hardware check runs the same steps and checks as the server boot process :1. MTPC check2. H3X or HCTX check3. Video Codec check4. Quad boot
ExitWhen exiting Multicam, a warning will appear to remind the operator that one disk wasdisconnected, and invite him to perform a hardware check to r
Table of ContentsTABLE OF CONTENTS IIIWHAT'S NEW? VII1. INTRODUCTION 11.1. Introduction to the Configuration of EVS Servers 11.2. Introduction to
Retrieving LogsIf you suspect that the drive disconnection in operation was not due to a severe diskfailure, but perhaps to the server being too promp
If you don’t need to retrieve the clips or the record trains, you don’t need to rebuild theRAID. In this case, select the 'Clear All Clips'
2.5.6. Importing and Exporting Keyword FilesIntroductionThe keyword file is a simple text file with a name of 8 characters and a .KWD extension.All ke
3. Press ENTER to export the keyword file from the EVS server to the USB key.4. Press OK to close the message box that appears when the keyword file h
3. Multicam Configuration3.1. Overview on User Interfaces3.1.1. IntroductionPreliminary RemarksConfiguration as Initial StepPrior to using Multicam, t
The following table provides an overview on the features available in each user interface:Configuration WindowTechnical Settings Operational SettingsS
Concurrent Modifications in the Remote Panel and theServer-Based ApplicationWhen a parameter is modified with the Remote Panel, and that parameter is
Accessing the Multicam Configuration WindowIn the Server-Based ApplicationTo access the Multicam Configuration window from the Multicam Setup window w
User InterfacesServer-Based User InterfaceThe following screenshot presents the 1sttab, and 1stpage of the Multicam Configurationwindow in the server-
3.1.3. Navigating and Editing in the MulticamConfiguration WindowIn the Server-Based ApplicationNavigation CommandsThe following table presents the co
2.5.6. Importing and Exporting Keyword Files 422.5.7. Exporting Log Files 433. MULTICAM CONFIGURATION 443.1. Overview on User Interfaces 443.1.1. Intr
Editing CommandsThe following table presents the commands to edit the configuration settings in theMulticam Configuration window when the field has be
In the Web-Based InterfaceNavigation and Editing CommandsThe navigation and editing commands in the web-based interface are the commonly usedcommands
Required Application RebootModifications to some parameters will only be applied after an application reboot. This ismentioned in the sections where t
3.1.4. Overview of the Setup Menus in the RemotePanelIntroductionWhen you work in XSensemode, the Technical and Operational Setup menus availableon t
3.1.5. Navigating and Editing in the Setup Menus ofthe Remote PanelIntroductionThe way you navigate and edit settings is identical in the Technical Se
Editing CommandsThe following table presents the commands to edit a setting in the Setup menus of theRemote Panel:Command description Command keySelec
3.2. Supported Configurations3.2.1. General Information on SupportedConfigurationsOverview on Supported Configuration TypesAn XS server, equipped with
Channel AssignmentThe following general principles apply to all configurations, and are valid for all EVSservers equipped with V3X or COHX boards:• Th
• The secondary links of the V3X boards correspond to the middle connectors of acodec module:◦ J5 for IN connectors◦ J3 for OUT connectors3.2.2. SD/HD
IN4/OUT1 IN3/OUT2 IN2/OUT3 IN1/OUT4#REC #PLAYPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.Link4 0 REC4 REC3 REC2 REC10 1 PLAY1 MIX1
3.8.3. Tally Settings 1673.9. Operation Tab 1693.9.1. Overview 1693.9.2. OSD Settings 1723.9.3. Audio Meters OSD Settings 1733.9.4. Clips Settings 175
IN6/OUT1 IN5/OUT2 IN4/OUT3 IN3/OUT4 IN2/OUT5 IN1/OUT6#REC #PLAYPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPr
Example: 4REC + 2PLAYThe BNC connectors to be used as record and play channels in a standard 4REC 2PLAYconfiguration need to be cabled as shown below:
3.2.3. General Principles on 3D and 1080pConfigurationsIntroductionThe 3D and 1080p configurations can be used on an XS server, using one of the follo
3.2.4. 3D/1080p Standard ConfigurationsAssignment PrinciplesThe following rules on connector assignments on the rear panel apply to 3D or 1080pconfigu
IN4/OUT1 IN3/OUT2 IN2/OUT3 IN1/OUT4#REC #PLAYPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.Link0 2 PLAY1A PLAY1B PLAY2A PLAY2B1 2 PL
Example: 3D/1080p Dual Link 1REC + 1PLAYThe BNC connectors to be used as recorder and play channels in a 3D or 1080p Dual Linkconfiguration 1REC + 1PL
IN6/OUT1 IN5/OUT2 IN4/OUT3 IN3/OUT4 IN2/OUT5 IN1/OUT6#REC #PLAYPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPrim.LinkSec.LinkPr
Example: 3D/1080p Dual Link 3REC + 1PLAYThe BNC connectors to be used as recorder and play channels in a 3D or 1080p Dual Linkconfiguration 3REC + 1PL
3.3. Server Tab3.3.1. OverviewServer TabThe Server tab consists of a single page in the basic or advanced mode in the server-based application. It cov
Setting Name Basic AdvancedTechnicalSetupIP Address X XSubnet Mask X XDefault Gateway X X3.3.2. Video and ReferenceVideo and Reference SettingsIntrodu
EVS Broadcast Equipment S.A.- November 2012VI Table of Contents
Field RateDescription Field frequency used (Hz).Both field rate and resolution give the video standard.Values 50.00 Hz (PAL) - default59.94 Hz (NTSC)5
CodecDescription Algorithm used to compress and decompress the video signal.The codecs available on the EVS server depend on the videostandard used, a
Recorded Lines (SD)Description Number of lines recorded from the left to the right of thepicture.The setting value depends on the selected video stand
Codec AvailabilityCodec Availability Depending on License CodesThe following table presents the codec availability for an XS server depending on theli
Codec-Related InformationBitrates and Recorded Lines in SD 525iCodec Type SD MJPEG Standard SD IMX (D10) DVCPro 50Bitrate 20-100 Mbps 30; 40; 50 Mbps
Bitrates and Horizontal Resolutions in HD 1080i/1080p(50 Hz)CodecHD MJPEGEVSHD MJPEGStandardHD MPEG2IntraDVCPro HD(only 1080i)AVCIntra 100Bitrate(Mbps
Bitrates and Horizontal Resolutions in HD 1080i/1080p(59.94 Hz)CodecHD MJPEGEVSHD MJPEGStandardHD MPEG2IntraDVCPro HD(only 1080i)AVCIntra100Bitrate(Mb
Bitrates and Horizontal Resolutions in HD 720p (50 Hz)HDMJPEGEVSHDMJPEGStandardHD MPEG2IntraDVCProHDAVC Intra100Bitrate(Mbps)20-360 20-360 20-360 100
Bitrates and Horizontal Resolutions in HD 720p(59.94 Hz)HDMJPEGEVSHDMJPEGStandardHD MPEG2IntraDVCProHDAVC Intra100Bitrate(Mbps)20-360 20-360 20-360 10
WarningSome video formats allowed on an XS server create clips that are not compatiblewith previous hardware. When an incompatible format is selected,
What's New?The changes linked to new features in version 11.1 are listed in the table below.In the configuration manual, the icon has been added
HD to SD SDI / SD SDI to HDDescription Allows adjusting the secondary phase of the mainframe, that isto say the relative phase of the:• HD SDI outputs
3.3.4. Interpolation SettingsIntroductionThe Interpolation settings are available on the Server tab in the server-based application(1stpage) and web-b
Vertical Interp. (Vertical Interpolation)Description Enables or disables the two-line interpolation process.Values • No (default)• YesFour LinesDescri
General DescriptionThe PC LAN settings allow the MTPC board of an EVS server to communicate andexchange information with other EVS hardware on a setup
3.4. Channels Tab3.4.1. OverviewChannels TabThe Channels tab consists of maximum nine pages in the advanced mode in the server-based application, and
Setting Name Basic AdvancedTechnicalSetupAudio settings P2 P2 T2.XAudio connectors X X XNumber of tracks X X XAudio full scale X XAncillary mode X XSa
Setting Name Basic AdvancedTechnicalSetupTimecode insertion settings — P9 —IN Loop settings XSD OUT settings XHD OUT settings X3.4.2. ChannelsBase Set
InputsDescription Number of logical record channels in the given configuration.The partition of the disk storage between these channels, andthe advanc
Base Config.Description Mode the EVS server is working in.The base configurations available depend on the server type,and on the valid license codes.V
3G/DualDescription Defines the interface the EVS server will use with the 3D or1080p standards:• The Dual Link interface consists of a pair of HD-SDI
Kommentare zu diesen Handbüchern